Menu 24.2.1 - System Maintenance - Information Name: P660RU-T3_T7 Routing: BRIDGE ZyNOS F/W Version: V3.40(AGY.0)_20061010 | 10/10/2006 ADSL Chipset Vendor: DMT FwVer: 3.2.0.7_B_TC, HwVer: T14F7_+ Standard: Multi-Mode LAN Ethernet Address: 00:xx:xx:xx:xx: IP Address: 192.168.1.1 IP Mask: 255.255.255.0 DHCP: None ---------------------------------------- Menu 1 - General Setup System Name= P660RU-T3_T7 Location= Contact Person's Name= Domain Name= Edit Dynamic DNS= No Route IP= No Bridge= Yes ---------------------------------------- Menu 3.2 - TCP/IP and DHCP Setup DHCP Setup DHCP= None Client IP Pool Starting Address= N/A Size of Client IP Pool= N/A Primary DNS Server= N/A Secondary DNS Server= N/A Remote DHCP Server= N/A TCP/IP Setup: IP Address= 192.168.1.1 IP Subnet Mask= 255.255.255.0 RIP Direction= Both Version= RIP-2B Multicast= IGMP-v2 IP Policies= Edit IP Alias= No ---------------------------------------- Menu 4 - Internet Access Setup ISP's Name= STK Encapsulation= RFC 1483 Multiplexing= LLC-based VPI #= 8 VCI #= 35 ATM QoS Type= UBR Peak Cell Rate (PCR)= 0 Sustain Cell Rate (SCR)= 0 Maximum Burst Size (MBS)= 0 My Login= N/A My Password= N/A ENET ENCAP Gateway= N/A IP Address Assignment= Static IP Address= 0.0.0.0 Network Address Translation= SUA Only Address Mapping Set= N/A ---------------------------------------- Menu 11 - Remote Node Setup 1. STK (ISP, SUA) 2. -IP-TV1 <- Проверял на разных позициях 3. ________ 4. ________ 5. ________ 6. ________ 7. IP-TV 8. ________ ---------------------------------------- Menu 11.1 - Remote Node Profile Rem Node Name= STK Route= None Active= Yes Bridge= Yes Encapsulation= RFC 1483 Edit IP/Bridge= No Multiplexing= LLC-based Edit ATM Options= No ---------------------------------------- Menu 11.6 - Remote Node ATM Layer Options VPI/VCI (LLC-Multiplexing or PPP-Encapsulation) VPI #= 8 VCI #= 35 ATM QoS Type= UBR Peak Cell Rate (PCR)= 0 Sustain Cell Rate (SCR)= 0 Maximum Burst Size (MBS)= 0 ---------------------------------------- Menu 11.1 - Remote Node Profile Rem Node Name= IP-TV Route= None Active= Yes Bridge= Yes Encapsulation= RFC 1483 Edit IP/Bridge= No Multiplexing= LLC-based Edit ATM Options= No ---------------------------------------- Menu 11.6 - Remote Node ATM Layer Options VPI/VCI (LLC-Multiplexing or PPP-Encapsulation) VPI #= 0 VCI #= 35 ATM QoS Type= UBR Peak Cell Rate (PCR)= 0 Sustain Cell Rate (SCR)= 0 Maximum Burst Size (MBS)= 0 ---------------------------------------- Menu 24.1 - System Maintenance - Status 03:15:30 Sat. Jan. 01, 2000 Node-Lnk Status TxPkts RxPkts Errors Tx B/s Rx B/s Up Time 1-1483 Up 241 0 0 0 0 1:17:23 2 N/A 0 0 0 0 0 0:00:00 3 N/A 0 0 0 0 0 0:00:00 4 N/A 0 0 0 0 0 0:00:00 5 N/A 0 0 0 0 0 0:00:00 6 N/A 0 0 0 0 0 0:00:00 7-1483 Up 4134 4328 0 0 0 1:36:15 8 N/A 0 0 0 0 0 0:00:00 My WAN IP (from ISP): 192.168.1.1 Ethernet: WAN: Status: 100M/Full Duplex Tx Pkts: 6163 Line Status: Up Collisions: 0 Rx Pkts: 5264 Upstream Speed: 886 kbps CPU Load = 8.10% Downstream Speed: 16397 kbp+ Press Command: COMMANDS: 1-Reset Counters TAB-Next Page ESC-Exit ---------------------------------------- Пробовал настроить и NAT Menu 15.2 - NAT Server Setup Rule Start Port No. End Port No. IP Address --------------------------------------------------- 1. Default Default 192.168.1.2 2. 8001 8100 192.168.1.2 3. 80 80 192.168.1.2 4. 21 21 192.168.1.2 5. 23 23 192.168.1.2 6. 0 0 0.0.0.0 7. 0 0 0.0.0.0 8. 0 0 0.0.0.0 9. 0 0 0.0.0.0 10. 0 0 0.0.0.0 11. 0 0 0.0.0.0 12. 0 0 0.0.0.0 ---------------------------------------------- main debug: prebuffering done 0 bytes in 69s - 0 kbytes/s main error: cannot pre fill buffer main warning: cannot create a stream_t from access main debug: removing module "access_udp" main debug: thread times: real 1m9.171875s, kernel 0m0.062500s, user 0m0.015625s main debug: thread 3808 joined (input/input.c:399) main debug: creating new input thread main debug: waiting for thread completion main debug: thread 3808 (input) created at priority 1 (input/input.c:261) main debug: `udp://@224.10.10.27:8027' gives access `udp' demux `' path `@224.10.10.27:8027' main debug: creating demux: access='udp' demux='' path='@224.10.10.27:8027' main debug: looking for access_demux module: 0 candidates main warning: no access_demux module matched "udp" main debug: creating access 'udp' path='@224.10.10.27:8027' main debug: looking for access2 module: 6 candidates access_udp debug: opening server=:0 local=224.10.10.27:8027 main debug: net: connecting to '[]:0@[224.10.10.27]:8027' main debug: looking for network module: 1 candidate ipv6 debug: 224.10.10.27: Host or service not found main debug: using network module "ipv6" main debug: removing module "ipv6" main debug: looking for network module: 1 candidate ipv4 debug: resolving :8027... ipv4 debug: resolving 224.10.10.27:8027... ipv4 debug: Winsock best interface is 1310724 ipv4 debug: IP_ADD_MEMBERSHIP multicast request main debug: using network module "ipv4" main debug: removing module "ipv4" main debug: using access2 module "access_udp" main debug: pre buffering